skiboot-5.4.0-rc1

skiboot-5.4.0-rc1 was released on Monday October 17th 2016. It is the first release candidate of skiboot 5.4, which will become the new stable release of skiboot following the 5.3 release, first released August 2nd 2016.

skiboot-5.4.0-rc1 contains all bug fixes as of skiboot-5.3.7 and skiboot-5.1.18 (the currently maintained stable releases).

For how the skiboot stable releases work, see Skiboot stable tree rules and releases for details.

The current plan is to release a new release candidate every week until we feel good about it. The aim is for skiboot-5.4.x to be in op-build v1.13, which is due by November 23rd 2016.

Over skiboot-5.3, we have the following changes:

New Features

  • Initial Trusted Boot support (see Secure and Trusted Boot Library (LibSTB) Documentation). There are several limitations with this initial release:

    • CAPP partition is not measured correctly

    • Only Nuvoton TPM 2.0 is supported

    • Requires hardware rework on late revision Habanero or Firestone boards in order to install TPM.

    • Add i2c Nuvoton TPM 2.0 Driver

    • romcode driver for POWER8 secure ROM

    • See Device tree docs for tpm and ibm,secureboot nodes

    • See main secure and trusted boot documentation.

  • Fast reboot for P8

    This makes reboot take an awful lot less time, somewhere between four and ten times faster than a full IPL. It is currently experimental and not enabled by default. You can enable the experimental support via nvram option:

    # nvram -p ibm,skiboot --update-config experimental-fast-reset=feeling-lucky

    WARNING: This has known bugs. For example, if you have used a device in CAPI mode, we will currently NOT reset it back to plain PCI. There are also some known issues in most simulators.

  • Support ibm,skiboot NVRAM partition with skiboot configuration options.

    • These should generally only be used if you either completely know what you are doing or need to work around a skiboot bug. They are not intended for end users.

    • Add support for supplying the kernel boot arguments from the bootargs configuration string in the ibm,skiboot NVRAM partition.

    • Enabling the experimental fast reset feature is done via this method.

  • Add support for nap mode on P8 while in skiboot

    • While nap has been exposed to the Operating System since day 1, we have not utilized low power states when in skiboot itself, leading to higher power consumption during boot. We only enable the functionality after the 0x100 vector has been patched, and we disable it before transferring control to Linux.

  • libflash: add 128MB MX66L1G45G part

  • Pointer validation of OPAL API call arguments.

    • If the kernel called an OPAL API with vmalloc’d address or any other address range in real mode, we would hit a problem with aliasing. Since the top 4 bits are ignored in real mode, pointers from 0xc.. and 0xd.. (and other ranges) could collide and lead to hard to solve bugs. This patch adds the infrastructure for pointer validation and a simple test case for testing the API

    • The checks validate pointers sent in using opal_addr_valid()

Documentation

There have been a number of documentation fixes this release. Most prominent is the switch to Sphinx (from the Python project) and ReStructured Text (RST) as the documentation format. RST and Sphinx enable both production of pretty documentation in HTML and PDF formats while remaining readable in their raw form to those with no knowledge of RST.

You can build a HTML site by doing the following:

cd doc/
make html

As always, documentation patches are very, very welcome as we attempt to document the OPAL API, the device tree bindings and important parts of OPAL internals.

We would like the Device Tree documentation to follow the style that can be included in the Device Tree Specification.

General

  • Make console-log time more readable: seconds rather than timebase Log format is now [SECONDS.(tb%512000000),LEVEL]

  • Flash (PNOR) code improvements

    • flash: Make size 64 bit safe This makes the size of flash 64 bit safe so that we can have flash devices greater than 4GB. This is especially useful for mambo disks passed through to Linux.

    • core/flash.c: load actual partition size We are downloading 0x20000 bytes from PNOR for CAPP, but currently the CAPP lid is only 40K.

    • flash: Rework error paths and messages for multiple flash controllers Now that we have mambo bogusdisk flash, we can have many flash chips. This is resulting in some confusing output messages.

  • core/init: Fix “failure of getting node in the free list” warning on boot.

  • slw: improve error message for SLW timer stuck

  • Centaur / XSCOM error handling

    • print message on disabling xscoms to centaur due to many errors

    • Mark centaur offline after 10 consecutive access errors

  • XSCOM improvements

    • xscom: Map all HMER status codes to OPAL errors

    • xscom: Initialize the data to a known value in xscom_read In case of error, don’t leave the data random. It helps debugging when the user fails to check the error code. This happens due to a bug in the PRD wrapper app.

    • chip: Add a quirk for when core direct control XSCOMs are missing

  • p8-i2c: Don’t crash if a centaur errored out

  • cpu: Make endian switch message more informative

  • cpu: Display number of started CPUs during boot

  • core/init: ensure that HRMOR is zero at boot

  • asm: Fix backtrace for unexpected exception

  • cpu: Remove pollers calling heuristics from cpu_wait_job This will be handled by time_wait_ms(). Also remove a useless smt_medium(). Note that this introduce a difference in behaviour: time_wait will only call the pollers on the boot CPU while cpu_wait_job() could call them on any. However, I can’t think of a case where this is a problem.

  • cpu: Remove global job queue Instead, target a specific CPU for a global job at queuing time. This will allow us to wake up the target using an interrupt when implementing nap mode. The algorithm used is to look for idle primary threads first, then idle secondaries, and finally the less loaded thread. If nothing can be found, we fallback to a synchronous call.

  • lpc: Log LPC SYNC errors as unrecoverable ones for manufacturing

  • lpc: Optimize SerIRQ dispatch based on which PSI IRQ fired

  • interrupts: Add new source ->attributes() callback

    This allows a given source to provide per-interrupt attributes such as whether it targets OPAL or Linux and it’s estimated frequency.

    The former allows to get rid of the double set of ops used to decide which interrupts go where on some modules like the PHBs and the latter will be eventually used to implement smart caching of the source lookups.

  • opal/hmi: Fix a TOD HMI failure during a race condition.

  • platform: Add BT to Generic platform

NVRAM

  • Support ibm,skiboot partition for skiboot specific configuration options

  • flash: Size NVRAM based on ECC for OpenPOWER platforms

    If NVRAM has ECC (as per the ffs header) then the actual size of the partition is less than reported by the ffs header in the PNOR then the actual size of the partition is less than reported by the ffs header.

PCI

  • Generic fixes

    • Claim surprise hotplug capability

    • Reserve PCI buses for RC’s slot

    • Update PCI topology after power change

    • Return slot cached power state

    • Cache power state on slot without power control

    • Avoid hot resets at boot time

    • Fix initial PCIe slot power state

    • Print CRS retry times It’s useful to know the CRS retry times before the PCI device is detected successfully. In PCI hot add case, it usually indicates time consumed for the adapter’s firmware to be partially ready (responsive PCI config space).

    • core/pci: Fix the power-off timeout in pci_slot_power_off() The timeout should be 1000ms instead of 1000 ticks while powering off PCI slot in pci_slot_power_off(). Otherwise, it’s likely to hit timeout powering off the PCI slot as below skiboot logs reveal:

      [5399576870,5] PHB#0005:02:11.0 Timeout powering off slot

  • PHB3

    • Override root slot’s prepare_link_change() with PHB’s

    • Disable surprise link down event on PCI slots

    • Disable ECRC on Broadcom adapter behind PMC switch

  • astbmc platforms

    • Support dynamic PCI slot. We might insert a PCIe switch to PHB direct slot and the downstream ports of the PCIe switch supports PCI hotplug.

CAPI

  • hw/phb3: Update capi initialization sequence

    The capi initialization sequence was revised in a circumvention document when a ‘link down’ error was converted from fatal to Endpoint Recoverable. Other, non-capi, register setup was corrected even before the initial open-source release of skiboot, but a few capi-related registers were not updated then, so this patch fixes it.

IPMI

  • core/ipmi: Set interrupt-parent property

    This allows ipmi-opal to properly use the OPAL irqchip rather than falling back to the event interface in Linux.

Mambo Simulator

  • Helpers for POWER9 Mambo.

  • mambo: Advertise available RADIX page sizes

  • mambo: Add section for kernel command line boot args Users can set kernel command line boot arguments for Mambo in a tcl script.

  • mambo: add exception and qtrace helpers

  • external/mambo: Update skiboot.tcl to add page-sizes nodes to device tree

Simics Simulator

  • chiptod: Enable ChipTOD in SIMICS

Utilities

  • pflash

    • fix harmless buffer overflow: fl_total_size was uint32_t not uint64_t.

    • Don’t try to write protect when writing to flash file

    • Misc small improvements to code and code style

    • makefile bug fixes

  • external/boot_tests

    • remove lid from the BMC after flashing

    • add the nobooting option -N

    • add arbitrary lid option -F

  • getscom / getsram / putscom: Parse chip-id as hex

    We print the chip-id in hex (without a leading 0x), but we fail to parse that same value correctly in getscom / getsram / putscom

    # getscom -l
...
80000000 | DD2.0 | Centaur memory buffer
# getscom -c 80000000 201140a
Error -19 reading XSCOM

    Fix this by assuming base 16 when parsing chip-id.

PRD

  • opal-prd: Fix error code from scom_read and scom_write

  • opal-prd: Add get_interface_capabilities to host interfaces

  • opal-prd: fix for 64-bit pnor sizes

  • occ/prd/opal-prd: Queue OCC_RESET event message to host in OpenPOWER

    During an OCC reset cycle the system is forced to Psafe pstate. When OCC becomes active, the system has to be restored to its last pstate as requested by host. So host needs to be notified of OCC_RESET event or else system will continue to remian in Psafe state until host requests a new pstate after the OCC reset cycle.

IBM FSP Based Platforms

  • fsp/console: Allocate irq for each hvc console

    Allocate an irq number for each hvc console and set its interrupt-parent property so that Linux can use the opal irqchip instead of the OPAL_EVENT_CONSOLE_INPUT interface.

  • platforms/firenze: Fix clock frequency dt property:

    [ 1.212366090,3] DT: Unexpected property length /xscom@3fc0000000000/i2cm@a0020/clock-frequency
  • HDAT: Fix typo in nest-frequency property

    nest-frquency -> nest-frequency

  • platforms/ibm-fsp: Use power_ctl bit when determining slot reset method

    The power_ctl bit is used to represent if power management is available. If power_ctl is set to true, then the I2C based external power management functionality will be populated on the PCI slot. Otherwise we will try to use the inband PERST as the fundamental reset, as before.

  • FSP/ELOG: Fix elog timeout issue

    Presently we set timeout value as soon as we add elog to queue. If we have multiple elogs to write, it doesn’t consider queue wait time. Instead set timeout value when we are actually sending elog to FSP.

  • FSP/ELOG: elog_enable flag should be false by default

    This issue is one of the corner case, which is related to recent change went upstream and only observed in the petitboot prompt, where we see only one error log instead of getting all error log in /sys/firmware/opal/elog.

POWER9

  • mambo: Make POWER9 look like DD2

  • flash: Move flash node under ibm,opal/flash/

    This changes the boot ABI, so it’s only active for P9 and later systems, even though it’s unrelated to hardware changes. There is an associated Linux change to properly search for this node as well.

  • core/cpu.c: Add OPAL call to setup Nest MMU

  • psi: On p9, create an interrupt-map for routing PSI interrupts

  • lpc: Add P9 LPC interrupts support

  • chiptod: Basic P9 support

  • psi: Add P9 support

Testing and Debugging

  • test/qemu: bump qemu version used in CI, adds IPMI support

  • platform/qemu: add BT and IPMI support Enables testing BT and IPMI functionality in the Qemu simulator

  • init: In debug builds, enable debug output to console

  • mem_region: Be a bit smarter about poisoning

    Don’t poison chunks that are already free and poison regions on first allocation. This speeds things up dramatically.

  • libc: Use 8-bytes stores for non-0 memset too

    Memory poisoning hammers this, so let’s be a bit smart about it and avoid falling back to byte stores when the data is not 0

  • fwts: add annotation for manufacturing mode

  • check: Fix bugs in mem region tests

  • Don’t set -fstack-protector-all unconditionally

    We set it already in DEBUG builds and we use -fstack-protector-strong in release builds which provides most of the benefits and is more efficient.

  • Build host programs (and checks) with debug enabled

    This enables memory poisoning in allocations and list checking among other things.

  • Add global DEBUG make flag

Contributors

Extending the analysis done for the last few releases, we can see our trends in code review across versions:

Release

csets

Ack

Reviews

Tested

Reported

5.0

329

15

20

1

0

5.1

372

13

38

1

4

5.2-rc1

334

20

34

6

11

5.3-rc1

302

36

53

4

5

5.4-rc1

278

8

19

0

4

This release has fewer changesets over previous 5.x first release candidates, but that is not indicative of the size or complexity of these changes.

Processed 278 csets from 31 developers A total of 17052 lines added, 4745 removed (delta 12307)

Developers with the most changesets

Stewart Smith

71

(25.5%)

Benjamin Herrenschmidt

50

(18.0%)

Claudio Carvalho

38

(13.7%)

Gavin Shan

20

(7.2%)

Oliver O’Halloran

18

(6.5%)

Mukesh Ojha

9

(3.2%)

Cyril Bur

7

(2.5%)

Russell Currey

7

(2.5%)

Vasant Hegde

7

(2.5%)

Pridhiviraj Paidipeddi

6

(2.2%)

Michael Neuling

6

(2.2%)

Alistair Popple

4

(1.4%)

Sam Mendoza-Jonas

3

(1.1%)

Vipin K Parashar

3

(1.1%)

Balbir Singh

3

(1.1%)

Mahesh Salgaonkar

3

(1.1%)

Frederic Barrat

3

(1.1%)

Chris Smart

2

(0.7%)

Jack Miller

2

(0.7%)

Patrick Williams

2

(0.7%)

Jeremy Kerr

2

(0.7%)

Suraj Jitindar Singh

2

(0.7%)

Milton Miller

2

(0.7%)

Shilpasri G Bhat

1

(0.4%)

Frederic Bonnard

1

(0.4%)

Joel Stanley

1

(0.4%)

Breno Leitao

1

(0.4%)

Anton Blanchard

1

(0.4%)

Nicholas Piggin

1

(0.4%)

Nageswara R Sastry

1

(0.4%)

Cédric Le Goater

1

(0.4%)

Developers with the most changed lines

Claudio Carvalho

6817

(38.2%)

Stewart Smith

4677

(26.2%)

Benjamin Herrenschmidt

2586

(14.5%)

Gavin Shan

1005

(5.6%)

Cyril Bur

509

(2.9%)

Mukesh Ojha

361

(2.0%)

Oliver O’Halloran

343

(1.9%)

Russell Currey

343

(1.9%)

Balbir Singh

227

(1.3%)

Pridhiviraj Paidipeddi

194

(1.1%)

Michael Neuling

121

(0.7%)

Cédric Le Goater

115

(0.6%)

Vipin K Parashar

68

(0.4%)

Alistair Popple

66

(0.4%)

Vasant Hegde

65

(0.4%)

Shilpasri G Bhat

45

(0.3%)

Suraj Jitindar Singh

41

(0.2%)

Nicholas Piggin

34

(0.2%)

Sam Mendoza-Jonas

33

(0.2%)

Jack Miller

32

(0.2%)

Nageswara R Sastry

32

(0.2%)

Jeremy Kerr

23

(0.1%)

Mahesh Salgaonkar

21

(0.1%)

Chris Smart

20

(0.1%)

Milton Miller

19

(0.1%)

Patrick Williams

11

(0.1%)

Frederic Barrat

6

(0.0%)

Anton Blanchard

3

(0.0%)

Frederic Bonnard

2

(0.0%)

Joel Stanley

2

(0.0%)

Breno Leitao

2

(0.0%)

Developers with the most lines removed

Cyril Bur

299

(6.3%)

Developers with the most signoffs (total 226)

Stewart Smith

219

(96.9%)

Alistair Popple

4

(1.8%)

Cyril Bur

1

(0.4%)

Jeremy Kerr

1

(0.4%)

Benjamin Herrenschmidt

1

(0.4%)

Developers with the most reviews (total 19)

Mukesh Ojha

5

(26.3%)

Andrew Donnellan

4

(21.1%)

Vasant Hegde

3

(15.8%)

Russell Currey

3

(15.8%)

Balbir Singh

2

(10.5%)

Cyril Bur

1

(5.3%)

Vaidyanathan Srinivasan

1

(5.3%)

Developers with the most test credits (total 0)

Developers who gave the most tested-by credits (total 0)

Developers with the most report credits (total 4)

Benjamin Herrenschmidt

1

(25.0%)

Li Meng

1

(25.0%)

Pridhiviraj Paidipeddi

1

(25.0%)

Gavin Shan

1

(25.0%)

Developers who gave the most report credits (total 4)

Gavin Shan

1

(25.0%)

Vasant Hegde

1

(25.0%)

Russell Currey

1

(25.0%)

Stewart Smith

1

(25.0%)